nav emailalert searchbtn searchbox tablepage yinyongbenwen piczone journalimg journalInfo journalinfonormal searchdiv searchzone qikanlogo popupnotification paper paperNew
2026, 05, v.57 1-9
铁合金冶炼用型焦性能的影响因素及发展方向
基金项目(Foundation): 国家自然科学基金(项目批准号:52374347); 陕西省科技厅2025年重点研发计划重点项目-秦创原产业创新聚集区“四链”融合(项目编号:2025CY-JJQ-141); 榆林市科技计划项目(项目编号:2024-SF-227)
邮箱(Email):
DOI: 10.16122/j.cnki.issn1001-1943.2026.05.001
投稿时间: 2026-05-07
投稿日期(年): 2026
修回时间: 2026-06-05
终审时间: 2026-06-22
终审日期(年): 2026
审稿周期(年): 1
发布时间: 2026-10-13
出版时间: 2026-10-13
移动端阅读
摘要:

碳质还原剂是铁合金冶炼的关键原料。相较于焦炭、兰炭等传统材料,以焦粉、煤粉为原料,通过冷压成型工艺制备的型焦,凭借其形状规则可控、水分低、可与其他还原剂复配等优势,展现出良好的技术与经济可行性,是极具前景的替代品。本文对铁合金冶炼用型焦的制备与应用进行了综述。型焦性能受到成型压力、下料速率、干燥温度、焦粉性质、水分添加量以及黏结剂等关键因素的综合影响。其中,黏结剂(无机、有机、复合)的种类、添加量与分布形态对成型强度尤为关键。目前,型焦在应用中仍面临热态强度不足、反应性不稳定、原料波动以及添加黏结剂可能导致灰分增高等挑战。未来研究需聚焦于原料稳定与分级利用、开发高性能低成本黏结剂,并协同调控型焦的高温强度与反应性,以推动其更广泛、高效的工业应用。

Abstract:

Carbonaceous reducing agents are crucial raw materials for ferroalloy smelting. Compared to traditional materials such as coke and semi-coke,formed coke( briquette),produced by cold-pressing coke or coal powder with binders,emerges as a promising alternative due to its controllable shape,low moisture,and compatibility with other reductants,offering both technical and economic advantages. This paper reviews the preparation and application of formed coke for ferroalloy smelting. Its performance is comprehensively influenced by multiple factors,including forming pressure,feeding rate,drying temperature,properties of coke powder,moisture content,and especially the type,dosage,and distribution of binders( inorganic,organic,composite). However,challenges still exist in practical application,such as insufficient hot strength,unstable reactivity,feedstock fluctuations,and potential ash increase caused by binders. Future research should focus on stabilizing raw materials,developing high-performance and low-cost binders,and synergistically optimizing the hot strength and reactivity of formed coke to facilitate its broader and more efficient industrial application.

参考文献

[1]龚嘉珺,王海娟.高碳铬铁冶炼过程影响因素的研究进展[J].铁合金,2024,55(1):9-16.

[2]Kleynhans E L J,Beukes J P,Van Zyl P G,et al. The effect of carbonaceous reductant selection on chromite prereduction[J]. Metallurgical and Materials Transactions B,2017,48B(2):827-840. DOI:10. 1007/s11663-016-0878-4.

[3]杨凯鑫.碳质还原剂反应活性研究[D].兰州:兰州理工大学,2024.

[4]都海龙,王健,程晓曼,等.以无烟煤代替部分焦炭生产锰硅合金的应用[J].铁合金,2021,52(1):13-16.

[5]Eidem P A,Tangstad M,Bakken J A. Measurement of material resistivity and contact resistance of metallurgical coke[J]. Proceedings of the INFACON XI,New Delhi,India,2007:18-21.

[6]杨亚飞,崔洁,朴美红,等.兰炭特性及替代燃料应用的研究进展[J].煤化工,2025,53(3):94-98,107.

[7]李树民,陶旭,王建新,等.大型铬铁矿热炉渣中Cr2O3含量影响因素研究与实践[J].铁合金,2024,55(5):13-16.

[8]王毅,邹冲,马成,等.硅铁冶炼用兰炭的调控制备与工业应用试验[J].铁合金,2024,55(1):19-26.

[9]Krogerus H,Lintumaa T,Jokinen P. Laboratory investigations of the electrical resistivity of cokes and smelting charge for optimizing operation in large ferrochrome furnaces[J]. 2006.

[10]王庶均,李岱.用蓝炭冶炼75%硅铁的探讨[J].铁合金,1987(1):20-21.

[11]田桦.焦粉制备冶金型焦过程黏结剂的选择[J].应用化工,2015,44(S1):171-172,177.

[12]冯兵,刘千帆.焦粉压块替代铁合金焦试验研究[J].甘肃冶金,2009,31(1):5-8.

[13]崔先云.浅谈型焦在锰硅合金生产中的应用[J].铁合金,2018,49(1):5-8.

[14]Yongbin Y,Qiongxiang Z,Tao J,et al. Study on preparation of high strength formed coke[C]//Proceedings of the 5th International Congress on the Science and Technology of Ironmaking,2009:429-433.

[15]高润贵,侯晓磊,陈凤,等.焦粉冷压成型黏结剂的选择研究[J].煤炭加工与综合利用,2021(7):77-82.

[16]周升国,李浩.铁合金型焦耐高温性能研究及市场分析[J].铁合金,2024,55(2):37-39,45.

[17]董寅瑞.煤沥青碳化行为与型焦固结强化研究[D].长沙:中南大学,2024.

[18]雒和明.添加剂对焦粉型焦性能的影响[J].粘接,2007(3):10-12.

[19]郑琼香.焦炭粉制备高强度型焦的工艺及机理研究[D].长沙:中南大学,2011.

[20]石会龙,刘焕荣,李成帅,等.半焦成型技术及型焦应用研究进展[J].工业催化,2018,26(7):11-14.

[21]Zhang G,Sun Y,Xu Y. Review of briquette binders and briquetting mechanism[J]. Renewable and Sustainable Energy Reviews,2018,82:477-487.

[22]Zhang Q,Li F,Luo M,et al. Influence of preparation process on briquette and form coke compressive strength[J]. IOP Conference Series:Materials Science and Engineering,2018,394:042055.

[23]常志伟.低阶粉煤制备民用洁净燃料及黏结机理研究[D].太原:太原理工大学,2021.

[24]Guo Z,Wu J,Zhang Y,et al. Briquetting optimization method for the lignite powder using response surface analysis[J]. Fuel,2020,267:117260.

[25]商建立.低阶煤热解粉焦表界面特性及提质研究[D].太原:太原理工大学,2024.

[26]刘长林,雒和明,苟国俊.焦粉成型技术[J].环境污染治理技术与设备,2002(12):73-75.

[27]蒋绪,侯党社,于雪,等.兰炭末制备冶金型焦过程焦煤的影响研究[J].现代盐化工,2017,44(4):53-54.

[28]马春山,余显军.焦粉成型技术的应用[J].中国氯碱,2011(8):46,48.

[29]艾沙江·斯拉木,王永刚,林雄超,等.三道岭兰炭粉制备冶炼用型焦的工艺研究[J].煤炭转化,2016,39(2):51-58.

[30]蒋绪,侯党社.废弃半焦粉制备型焦的共炭化工艺研究[J].价值工程,2012,31(18):46-47.

[31]Guo Z,Xu X,Zhu D,et al. Clean preparation of formed coke from semi-coke by the carbonated consolidation process[J]. ACS Omega,2023,8(30):27398-27409.

[32]赵巍,李远才,万鹏,等.影响型煤成型质量的工艺参数研究[J].煤炭科学技术,2012,40(6):121-124.

[33]武琳琳.粒度级配及外加水分对晋城无烟煤成型性影响研究[J].中国煤炭,2023,49(5):117-121.

[34]张林生.型煤黏结剂研究现状[J].广州化工,2012,40(11):62-64,71.

[35]张秋利,成璇,兰新哲,等.型煤的制备工艺对煤焦油产率的影响[J].煤炭转化,2013,36(2):71-73.

[36]杨永斌,钟强,姜涛,等.煤沥青型焦制备与固结机理[J].中南大学学报(自然科学版),2016,47(7):2181-2188.

[37]金雷,王雷,丁一慧,等.利用气煤和焦粉制备优质铸造焦的研究[J].洁净煤技术,2008(2):84-86.

[38]孟佳文,曾泽泉,刘勇进,等.制备工艺对民用型焦抗压强度及燃烧性能与污染物排放特性的影响[J].煤炭转化,2019,42(1):48-56.

[39]Yonghui S,Wenjin H,Qiaona M,et al. Effect of binder composition on the preparation of formed coke with lowrank coal[J]. International Journal of Coal Preparation and Utilization,2020,40(6):376-388.

[40]Zhao H,Yu J,Liu J,et al. Experimental study on the self-heating characteristics of Indonesian lignite during low temperature oxidation[J]. Fuel,2015,150:55-63.

[41]Lumadue M R,Cannon F S,Brown N R. Lignin as both fuel and fusing binder in briquetted anthracite fines for foundry coke substitute[J]. Fuel,2012,97:869-875.

[42]杨凤玲,韩海忠,曹希,等.生物质型煤的制备及微观结构分析[J].洁净煤技术,2015,21(1):6-10.

[43]Plancher H,Agarwal P K,Severns R. Improving form coke briquette strength[J]. Fuel Processing Technology,2002,79(2):83-92.

[44]王超凡,宋永辉,尹宁,等.强化剂对低变质粉煤制备型焦过程的影响研究[J].化学工业与工程,2023:1-9.

[45]黄光许,郝瑛轩,刘全润,等.神木烟煤气化型煤的制备及成型机理研究[J].中国煤炭,2012,38(9):83-85,90.

[46]Taylor J W,Coban A. Formed coke from lignite,and the critical role of air[J]. Fuel,1987,66(1):141-142.

[47]Taylor J W,Çoban A. Factors affecting the strength of formed coke made from lignite char[J]. Fuel,1987,66(9):1274-1280.

[48]李登新,吴家珊,宋永玮.煤与黏结剂的相互作用和型煤抗压强度的关系[J].煤炭转化,1992(4):76-82.

[49]李磊,马成,李彬,等.型焦强度评价方法选择及其热态强度性能优化[J].冶金能源,2026,45(1):37-42.

基本信息:

DOI:10.16122/j.cnki.issn1001-1943.2026.05.001

中图分类号:TF62

引用信息:

[1]杨欣豪,王刚,李彬,等.铁合金冶炼用型焦性能的影响因素及发展方向[J].铁合金,2026,57(05):1-9.DOI:10.16122/j.cnki.issn1001-1943.2026.05.001.

基金信息:

国家自然科学基金(项目批准号:52374347); 陕西省科技厅2025年重点研发计划重点项目-秦创原产业创新聚集区“四链”融合(项目编号:2025CY-JJQ-141); 榆林市科技计划项目(项目编号:2024-SF-227)

投稿时间:

2026-05-07

投稿日期(年):

2026

修回时间:

2026-06-05

终审时间:

2026-06-22

终审日期(年):

2026

审稿周期(年):

1

发布时间:

2026-10-13

出版时间:

2026-10-13

引用

GB/T 7714-2015 格式引文
MLA格式引文
APA格式引文